Crown molding and finish carpentry in Parkland, FL
Crown molding in Parkland homes, along with coffered and beamed ceilings, stair railings and large entry doors, is installed by Apperals Custom Woodwork. Every exterior door is planned around the City of Parkland's window and door permit packet, which sets the wind and product rules for a replacement.
- Common requests
- Stacked crown, coffered ceilings, pivot and double entry doors, stair railings
- Building permits
- City of Parkland Building Division
- Hurricane zone
- Broward HVHZ; Parkland's packet calls for ASCE 7 loads at 170 mph minimum
- Door approvals
- A valid Florida (FL) product approval or a Miami-Dade NOA, with sizes and pressures marked
- Character
- Founded in 1963 on former ranch land, still described by the city as rustic and country
From ranch land to large lots
Parkland began in 1963, when cattle farmer Bruce B. Blount and his father turned more than 1,000 acres into a city. Early buyers could pick up five-acre parcels, and the city has since grown from 420 acres to more than 8,000. Its history page still calls it a rustic, country community. That means big rooms, tall ceilings and wide entries, where stacked crown molding, coffered ceilings and oversized doors earn their keep.
Replacing an entry door: what Parkland’s packet asks for
On a Parkland finish job, the paperwork sits mostly with the exterior door. The state code puts every Broward address in its High Velocity Hurricane Zone, and Parkland’s window and door permit packet asks for:
- The Broward County Uniform Building Permit Application.
- The Broward County Uniform Retrofit Window and Door Schedule, which the county’s Board of Rules and Appeals made mandatory countywide on July 1, 2020.
- A Notice of Commencement when the project cost is over $2,500.
- A valid Florida product approval or Miami-Dade NOA, with the opening size, glazing type and design pressure highlighted.
- A layout that labels each opening and its wind zone, tied to the schedule by a mark.
The design numbers are specific. Broward requires ASCE 7 calculations at an ultimate wind speed of at least 170 mph. All of the county is treated as Exposure C, and one and two story houses can use the county’s voluntary wind load chart. A building with a mean roof height over 20 feet needs site-specific engineering instead.
Where a carpenter fits in
The door maker supplies the approval. The finish carpenter makes sure the door, the rough opening and the trim agree with it. On a pivot or double entry door, we confirm the approved size before the opening is framed or cut, set the unit to the installation instructions, and then case and trim it. A taller or wider opening goes to an engineer for sealed alteration plans first.
The city’s FAQ adds one more rule: products in exterior walls must be approved by the plans examiner before they go in, and the schedule is usually due before the tie beam inspection on new work.
Inside the house
Interior trim needs less paperwork. High Parkland ceilings suit stacked crown, beamed ceilings and wood and iron stair railings. Nearby, we also serve Coral Springs and Boca Raton.
What we build in Parkland
Quote for your Parkland project
Leave your number and we'll call you back to talk through the project and set a time to measure. Builders and designers can text plans to the same number.
That phone number didn't look right. Enter a 10-digit number and send it again.
We couldn't send your request. Please call (754) 264-2296 and we'll take it by phone.
Thank you. We'll call you back from (754) 264-2296. Finish your text in Messages if you'd like to send photos of the space.
Parkland questions
Do I need a permit to replace an exterior door in Parkland?
Yes. The city's permit FAQ lists replacement of exterior doors and windows as work that needs a permit. Parkland's window and door packet then sets out the forms, the product approvals and the wind design numbers the application must include.
Does Parkland accept Florida product approval or only Miami-Dade NOA for doors?
The city's packet accepts either a valid Florida (FL) product approval or a Miami-Dade Notice of Acceptance, as long as the opening sizes, glazing types and design pressures that apply are highlighted. The approval has to cover the door at the size you are installing.
What if the new door opening is bigger than the old one?
Then it is no longer a simple swap. When opening sizes change, Parkland's packet requires sealed, site-specific alteration plans from an engineer. The header, the framing and the door's approval all have to work for the new size.
Do I need a permit for crown molding in Parkland?
Usually not for trim alone, since the city ties permits to physical changes to a structure such as doors, windows and structural repairs. If crown work comes with lighting, framing or a new ceiling, call the Building Division at 954-753-5447 to check.
Sources for the local notes on this page